Intex Ultra Frame 18x52

Volume: 7000 Gallons
Build Type: Vinyl
POOL HAS BEEN FROZEN FOR OVER A MONTH!! THE HUGE BLOCK OF ICE IS STARTING TO SLOWLY MELT WITH THE ABOVE FREEZING TEMPERATURES THIS WEEK. NEW POOL ARRIVING TOMORROW. WILL SLOWLY START TO DRAIN WITH SUBMERSIBLE PUMP AFTER ALL ICE IS MELTED.
Put one 3” trichlor tablet in floater and put in pool since it will be in the 50s the next couple days and the ice is melting! Just want to have some source of FC since pool is closed but not covered. Ugh.
6 oz of Trichlor
$3.00 on Trichlor tablets/pucks
**FINISHED SMALL BOTTLE OF BLEACH** FC was much lower than expected yesterday. Dumped rest of bleach in pool and swirled it around. Will see how it holds up the rest of the winter since it is about to be below freezing again!
30 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.3
pH
60
TA
Ice finally melted. Ran robot. Scooped leaves/debris from bottom and surface of water. Added about 13 oz. of 7.5% bleach and swirled/brushed while robot was running. Will test water tomorrow! Water Temperature: 40 degrees Fahrenheit. Still crystal clear and no organics. :)
13 oz of Bleach • 7.5%
Vacuumed
Vacuumed
****NOT COVERING POOL FOR THE WINTER. WILL SCOOP LEAVES OUT AS NEEDED!****
Closed Pool
19.0
FC
0.0
CC
70
TA
Backwashed
Vacuumed
**FINISHED SMALL BOTTLE OF 43 OZ. BLEACH. ADDING SOME HOSE WATER BECAUSE WATER LEVEL IS TOO LOW TO BACKWASH BEFORE CLOSING!**
43 oz of Bleach • 7.5%
Brushed
**FINISHED BOTTLE OF 81 OZ. BLEACH AND A SMALL 43 OZ. BOTTLE!! Both are 7.5% LC.**
17 oz of Bleach • 7.5%
43 oz of Bleach • 7.5%
17.0
FC
0.0
CC
****GETTING READY TO CLOSE TOMORROW!!**** SLAM TIME!! :)
64 oz of Bleach • 7.5%
14.5
FC
0.0
CC
60
TA
Vacuumed
***FINISHED BOTTLE OF 7.5% BLEACH**
57 oz of Bleach • 7.5%
VERY unseasonably warm the past 4 days! Temperatures dropping again after Wednesday. Will close later this week!
24 oz of Bleach • 7.5%
****FINISHED ANOTHER BOTTLE OF 81 OZ. 7.5% BLEACH. BRINGING WATER TO SLAM LEVEL TO BEGIN CLOSING HOPEFULLY!****
81 oz of Bleach • 7.5%
***FINISHED 81 OZ. BOTTLE OF 7.5% BLEACH***
40 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.4
pH
60
TA
50
CYA
9.0
FC
0.0
CC
7.1
pH
70
TA
Brushed
8 oz of Bleach • 7.5%
Lowering pH to about 7.1 and started aerating!
24 oz of Dry Acid
8.5
FC
0.0
CC
7.6
pH
80
TA
100
CH
**ADDED 2 INCHES OF HOSE WATER AFTER LONG BACKWASH AND RINSE. RUNNING PUMP AND WILL TEST/ADD CHEMICALS LATER TODAY.** RESULTS BELOW ARE FROM BEFORE THE BACKWASH AND FILL WATER!!
Backwashed
9.0
FC
0.0
CC
7.6
pH
Brushed
Vacuumed
10.5
FC
0.0
CC
7.6
pH
70
TA
**ADDED SOME HOSE WATER TO HELP DILUTE FC AND GET READY TO START CLOSING THIS WEEK (backwashing + getting ph in check).** VERY WINDY AND LOTS OF LEAVES!! Scooping them out all day and emptying skimmer basket every couple hours. Ugh.
Brushed
12.5
FC
0.0
CC
60
TA
50
CYA
**UNABLE TO GET ACCURATE PH READING DUE TO HIGH FC. WATER TEMPERATURE IS ONLY 52 DEGREES SO I AM LETTING THE SAMPLE BOTTLE WARM UP INSIDE A LITTLE BEFORE TESTING CYA.**
**TRICHLOR TABLET DISSOLVED. REMOVED FLOATER FROM POOL AND WILL ONLY BE USING BLEACH FROM NOW ON.**
13.0
FC
0.0
CC
70
TA
8 oz of Trichlor
16 oz of Bleach • 7.5%
9.0
FC
0.0
CC
7.6
pH
**ADDING AN INCH OF HOSE WATER.** Results above are from before I added the fill water!
10.0
FC
0.0
CC
7.4
pH
60
TA
Vacuumed
11.5
FC
0.0
CC
**Added about a half-inch (or slightly less?) of hose water.**
**TOOK TRICHLOR TABLET AND FLOATER OUT OF THE POOL. TABLET WAS DISSOLVED.**
13.0
FC
0.0
CC
60
TA
40
CYA
$3.00 on Trichlor tablets/pucks
13.5
FC
0.0
CC
60
TA
Vacuumed
Brushed
FC testing reagent refill arrived!! :)
16 oz of Bleach • 7.5%
**FC IS OVER 6 PPM. WILL TEST AGAIN WHEN R-0871 REFILL ARRIVES!!**
7.6
pH
60
TA
VERY HEAVY RAIN THE PAST 2 DAYS. Accumulated 1.5 - 2 inches of water. LOTS OF LEAVES!!!!! Still can’t test FC accurately until reagent arrives. Just using the basic kit to make sure it is at least 5ppm for now.
HAS BEEN RAINING NONSTOP SINCE LAST NIGHT!
6 oz of Trichlor
Brushed
8 oz of Bleach • 7.5%
18 oz of Dry Acid
$14.00 on Test Kit Reagents
RAN OUT OF R-0871 REAGENT! :( Can’t test FC until it arrives. Ordered from TFTestKits!
ADDED DRY ACID AND AERATING TO DROP TA TO 60!
10.0
FC
0.0
CC
7.6
pH
70
TA
$2.50 on Trichlor tablets/pucks
**FINISHED SMALL BOTTLE OF BLEACH!**
19 oz of Bleach • 7.5%
Vacuumed
10.0
FC
0.0
CC
7.4
pH
80
TA
100
CH
40
CYA
$8.00 on Dry Acid (pH-Down, sodium bisulfate)
16 oz of Bleach • 7.5%
Brushed
**ADDED AN INCH OF HOSE WATER. WILL TEST LATER!**
8 oz of Bleach • 7.5%
**FINISHED 7 LB BAG OF DRY ACID!**
**FINISHED SMALL BOTTLE OF BLEACH!**
18 oz of Dry Acid
32 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.6
pH
70
TA
ADDING ABOUT AN INCH OF HOSE WATER POST-BACKWASH. WILL TEST WATER IN A FEW HOURS!!
Backwashed
Vacuumed
WOKE UP TO SKIMMER FILLED BEYOND CAPACITY WITH LEAVES AND PUMP MAKING WEIRD NOISES SINCE IT WAS CLOGGED. CLEANED IT ALL OUT, USED NET TO GET EXTRA LEAVES, VACUUMED, AND ADDED LOTS OF EXTRA HOSE WATER BEFORE I DO A GOOD BACKWASH!! WILL LIKELY WILL ADD EVEN MORE WATER AFTERWARDS. IT IS A MESS!!
16 oz of Bleach • 7.5%
2.8 oz of Dry Acid
NEW BOTTLE OF BLEACH IS ONLY 43 OUNCES LOL
8.5
FC
0.0
CC
7.5
pH
60
TA
50
CYA
Brushed
**ADDED pH DOWN (1 cup...to drop pH from 7.4 to 7.2) TO LOWER TA TO 60**
**FINISHED BOTTLE OF BLEACH**
16.5 oz of Bleach • 7.5%
8 oz of Dry Acid
8.5
FC
0.0
CC
7.4
pH
70
TA
**ADDED ABOUT A HALF-INCH OF HOSE WATER**
Vacuumed
8 oz of Dry Acid
24 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.5
pH
70
TA
**Dropping pH to 7.2 and aerating to lower TA!**
16 oz of Dry Acid
16 oz of Bleach • 7.5%
Windy with lots of leaves blowing! Will be fishing out leaves and emptying skimmer basket all day. Wahhhh.
8.0
FC
0.0
CC
7.6
pH
80
TA
Vacuumed Brushed
**ADDED ABOUT 1/4 INCH OF HOSE WATER.**
8 oz of Bleach • 7.5%
**RAINY AND WINDY WITH LEAVES FALLING...oh boy!**
8.5 oz of Bleach • 7.5%
8.5
FC
0.0
CC
7.5
pH
70
TA
Putting an unnecessary cup of bleach in just so I don’t have to worry about it the rest of the day and tomorrow!!
8 oz of Bleach • 7.5%
9.5
FC
0.0
CC
7.4
pH
70
TA
12 oz of Dry Acid
7.5
pH
**FINISHED BOTTLE OF BLEACH**
25 oz of Bleach • 7.5%
Brushed
18 oz of Dry Acid
8 oz of Bleach • 7.5%
9.0
FC
0.0
CC
7.8
pH
80
TA
100
CH
40
CYA
8 oz of Bleach • 7.5%
ADDED A LITTLE BIT OF HOSE WATER AFTER A QUICK, HALF-ASSED VACUUM.
Brushed
Vacuumed
16 oz of Bleach • 7.5%
HEAVY WINDS AND LOTS OF LEAVES!! Scooping and cleaning out skimmer periodically throughout the day!!
$23.00 on Dry Acid (pH-Down, sodium bisulfate)
69 °F
TEMP
8 oz of Bleach • 7.5%
16 oz of Bleach • 7.5%
**FINISHED BOTTLE OF BLEACH**
45 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.8
pH
80
TA
68 °F
TEMP
8 oz of Bleach • 7.5%
8 oz of Bleach • 7.5%
8.5
FC
0.0
CC
7.7
pH
80
TA
69 °F
TEMP
16 oz of Bleach • 7.5%
**ADDED OVER AN INCH OF HOSE WATER!!**
8 oz of Bleach • 7.5%
8.5
FC
0.0
CC
7.6
pH
80
TA
65 °F
TEMP
**FINISHED BOTTLE OF BLEACH**
**FINISHED CONTAINER OF DRY ACID**
11 oz of Dry Acid
20 oz of Bleach • 7.5%
**Added a TINY bit of hose water** Adding chlorine, running pump a few hours, and will test water later, if I feel like it!
32 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.6
pH
70
TA
64 °F
TEMP
Vacuumed
Brushed
3 oz of Dry Acid
24 oz of Bleach • 7.5%
6.0
FC
0.0
CC
7.6
pH
80
TA
61 °F
TEMP
65 °F
TEMP
**ADDED A LITTLE HOSE WATER.**
18 oz of Bleach • 7.5%
**ADDING MORE HOSE WATER YET AGAIN (water needs to warm up before I can patch!!)** Will test water after running pump for a few hours.
Vacuumed Brushed
**FINISHED BOTTLE OF BLEACH!**
18 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.3
pH
70
TA
67 °F
TEMP
RANDOM NOTE: Tap water TA is 300 Tap water pH is around 8.0!! :(
**ADDED A SMALL AMOUNT OF HOSE WATER (a half inch at most).** Pump is running and I will test water tonight and add chemicals if necessary. :)
16 oz of Bleach • 7.5%
15 oz of Dry Acid
16 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.6
pH
80
TA
100
CH
40
CYA
69 °F
TEMP
**ADDED A LITTLE BIT OF HOSE WATER. THERE ARE A COUPLE NEW SMALL LEAKS THAT NEED PATCHED. UGH!**
70 °F
TEMP
18 oz of Bleach • 7.5%
6 oz of Dry Acid
8.5
FC
0.0
CC
7.6
pH
70
TA
72 °F
TEMP
16 oz of Bleach • 7.5%
Vacuumed
ADDED ABOUT AN INCH OF HOSE WATER. Going to run robot and let it circulate for a bit and then will test/balance water this afternoon!
**FINISHED BOTTLE OF BLEACH**
8 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.4
pH
60
TA
75 °F
TEMP
4 oz of Dry Acid
16 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.6
pH
**ADDED ABOUT A HALF INCH OF HOSE WATER** Test results above are from BEFORE I added the fill water.
16 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.6
pH
60
TA
75 °F
TEMP
Vacuumed
8 oz of Bleach • 7.5%
79 °F
TEMP
13 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.4
pH
70
TA
40
CYA
Brushed
14 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.3
pH
79 °F
TEMP
76 °F
TEMP
8 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.3
pH
70
TA
**1.5-2” RAIN ACCUMULATION FROM LAST NIGHT!**
Vacuumed
76 °F
TEMP
**ADDED A LIL BIT OF HOSE WATER.**
****FINISHED BOTTLE OF BLEACH****
25 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.2
pH
70
TA
40
CYA
8 oz of Bleach • 7.5%
14 oz of Dry Acid
8.5
FC
0.0
CC
7.6
pH
**Added a TINY bit of hose water. About 1/4 of an inch. I am pretty sure there’s a couple more small holes on bottom floor that need patched. Ugh.**
16 oz of Bleach • 7.5%
Brushed
8 oz of Dry Stabilizer
8.5
FC
0.0
CC
7.6
pH
70
TA
40
CYA
75 °F
TEMP
Vacuumed
16 oz of Bleach • 7.5%
16 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.3
pH
78 °F
TEMP
Vacuumed
8.2 oz of Dry Acid
9.5
FC
0.0
CC
7.7
pH
70
TA
78 °F
TEMP
**EMPTIED REST OF BLEACH (approximately 21 oz.) RIGHT BEFORE THE RAIN STARTED.** Will test when it stops. Today is the last day of rain for a while. :)
21 oz of Bleach • 7.5%
16 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.6
pH
70
TA
100
CH
80 °F
TEMP
**HEAVY RAINFALL LAST NIGHT AND THIS MORNING!! ABOUT 1.5-2 INCHES AS OF NOW. POOL IS FILLED TO MAX CAPACITY AND I MAY NEED TO DRAIN A LITTLE IF THIS CONTINUES. RUNNING PUMP 24 HOURS!**
12 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.4
pH
70
TA
79 °F
TEMP
79 °F
TEMP
8 oz of Bleach • 7.5%
Brushed
**ADDED LESS THAN AN INCH OF HOSE WATER.**
8 oz of Dry Stabilizer
24 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.4
pH
Vacuumed
$10.00 on Test Kit Reagents
$16.00 on Dry Stabilizer
8 oz of Dry Acid
**FINISHED BOTTLE OF BLEACH**
17 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.6
pH
70
TA
78 °F
TEMP
2.5 oz of Dry Acid
16 oz of Bleach • 7.5%
5.5
FC
0.0
CC
7.6
pH
81 °F
TEMP
16 oz of Bleach • 7.5%
8.5
FC
0.0
CC
7.6
pH
70
TA
30
CYA
82 °F
TEMP
Vacuumed Backwashed
**GOT LOTS OF RAIN LAST NIGHT (2 inches approximately). POOL FILLED TO MAXIMUM CAPACITY.** DRAINED AN INCH FROM BACKWASHING/RINSE/WASTE.
Brushed
24 oz of Bleach • 7.5%
LOTS of very very heavy rain throughout the whole day! :( At least an inch of water accumulation as of right now.
8 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.4
pH
70
TA
84 °F
TEMP
8.0
FC
0.0
CC
7.5
pH
84 °F
TEMP
**FINISHED BOTTLE OF BLEACH**
16 oz of Bleach • 7.5%
8.5
FC
0.0
CC
7.3
pH
70
TA
9 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.2
pH
70
TA
100
CH
83 °F
TEMP
***ADDING APPROXIMATELY 2 INCHES OF HOSE WATER AFTER A MUCH NEEDED BACKWASH AND RINSE***
Backwashed Brushed
Vacuumed
**DROPPING PH TO 7.0-7.2 AND BEGINNING AERATION AGAIN TO DROP ALKALINITY MORE.** Had some semi-heavy rain earlier this afternoon.
24 oz of Bleach • 7.5%
16 oz of Dry Acid
8.0
FC
0.0
CC
7.4
pH
80
TA
8 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.2
pH
84 °F
TEMP
12 oz of Bleach • 7.5%
20 oz of Dry Acid
16 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.7
pH
90
TA
Vacuumed
**FINISHED BOTTLE OF BLEACH**
17 oz of Bleach • 7.5%
16 oz of Bleach • 7.5%
**HEAVY RAIN STORM!! About 1.5 inches of accumulation.**
24 oz of Bleach • 7.5%
6.0
FC
0.0
CC
7.3
pH
80
TA
83 °F
TEMP
Vacuumed
Vacuumed
Added less than a half-inch of hose water. Not losing AS much water daily since patching 3 holes! Yay!
Ordered more pH Down from Leslie’s. Supposed to arrive by 8/28!
$21.00 on Dry Acid (pH-Down, sodium bisulfate)
**AERATING TO INCREASE PH. USED THE REST OF MY PH DOWN TO LOWER IT TO 7.2**
15 oz of Dry Acid
24 oz of Bleach • 7.5%
6.0
FC
0.0
CC
7.6
pH
90
TA
80 °F
TEMP
Vacuumed
7.0
FC
0.0
CC
7.6
pH
80 °F
TEMP
**FINISHED BOTTLE OF BLEACH**
17 oz of Bleach • 7.5%
Vacuumed
6.5
FC
0.0
CC
7.6
pH
80
TA
100
CH
77 °F
TEMP
16 oz of Bleach • 7.5%
**PATCHED A FEW LEAKS ON POOL FLOOR AND ADDED 2 INCHES OR SO OF HOSE WATER**
7.0
FC
0.0
CC
7.4
pH
Vacuumed
16 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.2
pH
80
TA
75 °F
TEMP
16 oz of Bleach • 7.5%
15 oz of Dry Acid
7.5
FC
0.0
CC
7.6
pH
80
TA
75 °F
TEMP
Vacuumed
8.0
FC
0.0
CC
7.5
pH
77 °F
TEMP
16 oz of Bleach • 7.5%
Added a tiny bit of fill water and used hose to aerate a little.
**TRYING TO AERATE THE PH UP BUT IT’S TAKING FOREVER! WANT TO GET MY TA TO 60 SINCE I AM ADDING HOSE WATER ALMOST DAILY. FILL WATER TA IS 300!!!!**
8.0
FC
0.0
CC
7.2
pH
80
TA
40
CYA
**FINISHED BOTTLE OF BLEACH**
16 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.1
pH
80
TA
80 °F
TEMP
Vacuumed
**ADDED A HALF INCH OF HOSE WATER**
80 °F
TEMP
24 oz of Dry Acid
$12.00 on Other • Patch repair kit
9.0
FC
0.0
CC
7.6
pH
90
TA
8 oz of Bleach • 7.5%
Vacuumed
11 oz of Bleach • 7.5%
80 °F
TEMP
Brushed
**ADDED A COUPLE INCHES OF HOSE WATER AFTER BACKWASH AND RINSE. ALSO TOOK TRICHLOR TABLET OUT OF FLOATER SINCE IT WAS BREAKING AND PIECES WERE ON THE FLOOR!!!!! HAD TO BRUSH TO DISSOLVE THE MESS. Ugh!**
Backwashed
Put one 3” trichlor puck in a floater tied onto a string and dangling in front of the return jet. Likely won’t be there long since it came from the same batch as my other defective tablets but need to get a little more CYA into the water and I’m out of granules. We’ll see how long this lasts. 2:30 PM UPDATE: I took it out after a couple hours, hence why I guessed the amount of trichlor used as 3 oz. since it wasn’t there very long.
3 oz of Trichlor
8.0
FC
0.0
CC
7.6
pH
80
TA
100
CH
8 oz of Bleach • 7.5%
**ADDED LESS THAN A 1/2 INCH OF HOSE WATER WHILE RUNNING ROBOT. IT RAINED EARLIER, ALSO.**
Vacuumed
24 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.4
pH
80
TA
83 °F
TEMP
16 oz of Bleach • 7.5%
7.2
pH
85 °F
TEMP
Vacuumed
12 oz of Dry Acid
8.0
FC
0.0
CC
7.3
pH
80
TA
8.5
FC
0.0
CC
7.3
pH
80
TA
83 °F
TEMP
7 oz of Dry Acid
8.5
FC
0.0
CC
7.6
pH
80
TA
85 °F
TEMP
Vacuumed Brushed
85 °F
TEMP
**FINISHED BOTTLE OF BLEACH**
34 oz of Bleach • 7.5%
$15.75 on Test Kit Reagents
6 oz of Dry Acid
8.0
FC
0.0
CC
7.7
pH
80
TA
40
CYA
14 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.7
pH
80
TA
84 °F
TEMP
84 °F
TEMP
Vacuumed
**ADDED LESS THAN AN INCH OF HOSE WATER**
16 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.6
pH
80
TA
17 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.6
pH
80
TA
85 °F
TEMP
Vacuumed
TA OF FILL WATER: 300!!! (Tested out of sheer boredom, lol)
9.0
FC
0.0
CC
7.5
pH
80
TA
82 °F
TEMP
**ADDED ABOUT A HALF INCH OF HOSE WATER DUE TO SPLASH-OUT AND EVAPORATION!**
Vacuumed
**FINISHED BOTTLE OF BLEACH**
40 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.3
pH
85 °F
TEMP
8.0
FC
0.0
CC
7.3
pH
70
TA
40
CYA
**SET TIMER ON PUMP TO SHUT OFF AT 10:45 PM**
8 oz of Bleach • 7.5%
9 oz of Dry Acid
8.0
FC
0.0
CC
7.7
pH
80
TA
100
CH
81 °F
TEMP
Vacuumed
**ADDED SOME HOSE WATER.**
32 oz of Bleach • 7.5%
7.0
FC
0.0
CC
7.4
pH
Brushed
8 oz of Bleach • 7.5%
6.5 oz of Dry Stabilizer
Ordered new thermometer via Amazon!
$10.00 on Accessories
7.0
FC
0.0
CC
7.6
pH
70
TA
**ADDED ABOUT 1/4 INCH OF HOSE WATER WHILE ROBOT WAS RUNNING**
Vacuumed
80 °F
TEMP
CYA dot is still kind of visible at the top of 40 and bottom of 30. Did not log result since I am unsure after doing test twice. Adding dry stabilizer tomorrow morning! I want it to be a solid 40, not right on the border to where I can’t really make the distinction between 40 and 30.
9.5
FC
0.0
CC
7.6
pH
70
TA
**FINISHED BOTTLE OF BLEACH**
32 oz of Bleach • 7.5%
Brushed
Vacuumed
8 oz of Bleach • 7.5%
8.0
FC
0.0
CC
7.3
pH
70
TA
8 oz of Bleach • 7.5%
11 oz of Dry Acid
7.5
FC
0.0
CC
7.8
pH
80
TA
75 °F
TEMP
17 oz of Bleach • 7.5%
****ADDED LESS THAN AN INCH OF HOSE WATER.****
Brushed
8.0
FC
0.0
CC
7.6
pH
80
TA
40
CYA
16 oz of Bleach • 7.5%
7.5
FC
0.0
CC
7.4
pH
80
TA
100
CH
78 °F
TEMP
Vacuumed
ADDING ABOUT 2 INCHES OF HOSE WATER AFTER A MUCH NEEDED BACKWASH AND RINSE. RUNNING PUMP AND WILL TEST WATER AGAIN IN A FEW HOURS.
Backwashed
8 oz of Dry Acid
**FINISHED LAST 10% LC BOTTLE**
22 oz of Bleach • 10%
7.0
FC
0.0
CC
7.6
pH
80
TA
40
CYA
18 oz of Bleach • 10%
6.0
FC
0.0
CC
7.5
pH
Brushed
Vacuumed
7.0
FC
0.0
CC
7.4
pH
70
TA
78 °F
TEMP
8 oz of Bleach • 10%
16 oz of Dry Acid
8.0
FC
0.0
CC
8.2
pH
80
TA
24 oz of Bleach • 10%
Vacuumed
8.5
FC
0.0
CC
8.2
pH
80
TA
80 °F
TEMP
32 oz of Bleach • 10%
Test results below are from before I turned the pump on (did not run at all last night...oops). Pump shut off yesterday evening around 7 PM and not turned back on until around 7:20 AM this morning after I collected water sample. Not sure if the lack of circulation and heavy accumulation of rain from last night without the pump running will make results inaccurate. Will retest and log results again after pump runs for several hours.
6.0
FC
0.5
CC
8.0
pH
80
TA
LOTS of heavy rain accumulation last night! Pool filled to max capacity! Running pump 24 hours! pH Down finally arriving tomorrow!!
24 oz of Bleach • 10%
**FINISHED BOTTLE OF 7.5% BLEACH**
7 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.8
pH
80
TA
100
CH
40
CYA
82 °F
TEMP
Added less than a half inch of hose water.
18 oz of Bleach • 7.5%
5.5
FC
0.0
CC
32 oz of Bleach • 7.5%
5.5
FC
0.0
CC
7.8
pH
****ADDING ABOUT 2 INCHES OF HOSE WATER. GOING TO TRY TO FIND AND PATCH THE LEAK SINCE THERE HAS TO BE ONE!! Water test results above are from BEFORE I added the extra fill water!!**** ADDING 4 CUPS OF BLEACH, RUNNING PUMP FOR A FEW HOURS AND WILL RETEST.
24 oz of Bleach • 7.5%
6.5
FC
0.0
CC
7.7
pH
70
TA
40
CYA
85 °F
TEMP
**FINISHED BOTTLE OF 10% LC**
22 oz of Bleach • 10%
Vacuumed
$10.70 on Other • Mesh surface skimmer net
$13.88 on Test Kit Reagents
$22.63 on Test Kit Reagents
6.5
FC
0.0
CC
7.6
pH
70
TA
9.3 oz of Dry Stabilizer
18 oz of Bleach • 10%
5.5
FC
0.0
CC
7.6
pH
85 °F
TEMP
**ADDED ABOUT AN INCH OF HOSE WATER**
16 oz of Bleach • 10%
7.5
FC
0.0
CC
7.8
pH
Vacuumed
40 oz of Bleach • 10%
6.0
FC
0.0
CC
7.7
pH
85 °F
TEMP
Backwashed
24 oz of Bleach • 10%
6.0
FC
0.0
CC
7.5
pH
83 °F
TEMP
8 oz of Bleach • 10%
**FINISHED BOTTLE OF BLEACH AND 10 POUND TUB OF pH DOWN**
25 oz of Bleach • 7.5%
Brushed
**FINISHED 10 LB. TUB OF DRY ACID. ORDERED MORE YESTERDAY!!**
7 oz of Dry Acid
32 oz of Bleach • 7.5%
4.5
FC
0.0
CC
7.6
pH
60
TA
100
CH
84 °F
TEMP
$20.00 on Dry Acid (pH-Down, sodium bisulfate)
24 oz of Bleach • 7.5%
6.0
FC
0.0
CC
7.7
pH
70
TA
**FINISHED BOTTLE OF BLEACH**
Vacuumed
17 oz of Bleach • 7.5%
24 oz of Bleach • 7.5%
8.5 oz of Dry Acid
7.0
FC
0.0
CC
7.8
pH
60
TA
82 °F
TEMP
40 oz of Bleach • 7.5%
6.0
FC
0.0
CC
7.5
pH
70
TA
82 °F
TEMP
ADDED A TINY BIT OF HOSE WATER BECAUSE OF EVAPORATION. SUPPOSED TO RAIN TODAY BUT NOT COUNTING ON IT...
****FINISHED BOTTLE OF 10% LC**** Didn’t need to add but did anyways in case it rains and so I don’t have to worry about it the rest of the day!
28 oz of Bleach • 10%
9 oz of Dry Acid
7.0
FC
0.0
CC
7.8
pH
70
TA
83 °F
TEMP
Vacuumed
24 oz of Bleach • 10%
5.5
FC
0.0
CC
7.5
pH
30
CYA
86 °F
TEMP
9.0
FC
0.0
CC
7.7
pH
70
TA
16 oz of Bleach • 10%
7.5
FC
0.0
CC
7.6
pH
85 °F
TEMP
10.5
FC
0.0
CC
70
TA
85 °F
TEMP

My new REAL pool!!

Volume: 7500 Gallons
Build Type: Vinyl